RS-232 to RS-422/485 Isolated bi-directional Interface Converter
The AN-OS-RS-232/422/485 is a series of a bi-directional interface converters.
The AN-OS-RS-232/422/485 is a series of a bi-directional interface converters. AN-OS-RS-232/422/485 optically isolate and convert unbalanced, full or half-duplex RS-232 signals to optically isolated, balanced, full or halfduplex RS-422 or RS-485 signals at baud rates up to 115.2 kbps. These units also surge suppress the RS-422/485 lines.
● Electric interface: RS-232C interface DB25 hole connector RS-422/485 interface 4-bit terminal or RJ-11 port
● Transmission media: twisted-pair cable or shielded cable
● Working mode: asynchronous half or full duplex
● Signal indication: a dual color signal indication light indicates TD, RD data
● Isolation: isolation voltage 3500VRMS 500VDC sequence
● Power supply: serial port electricity stealing at RS-232 end. External power supply connecting at RS-422/485 end
Application fields:
● Point to point, point to multi-point communication
● Industrial distribution system, industrial control automation
● Road traffic control automation
● Closed circuit monitoring
● Security protection system
● Intelligent card, check on work attendance gate safety system
Interface
Conforms to EIA /RS-232 and RS-422/485 standards.
Connectors and signals
The ATC-107 has a DB-25 female connector on the RS-232 side and a terminal block connector on the RS-422/485 side
RS-232 Side:
Connector: DB-25 Female.
Signals:Unit will be connected into a DTE interface.
Use Pins 3 (TXD)、2 (RXD) and 7 (Near side ground) .
Use Pin 2、4、 20 to power from unit’s RS-232 side.
RS-422/485 Side:
RS-422 Connector: 4 position terminal block : (1)T+ (2)T-、(3)R-、(4)R+.
RS-485 Connector: 4 position terminal block: (1)485+, (2)485-.
Signals: Dual-duplex or Half-duplex two-wire/four-wire operation only.
Data Rate:
300 to 115.2 KBPS, up to 1.2km at 38.4 KBPS.
Sending Control
Unit can use handshake lines to power the converter, no handshaking is required to control the RS-422/RS-485 driver. the RS-485 driver is automatically enabled during each spacing state on the RS-232 side. During the marking or idle state, the RS-485 driver is disabled and the data lines are held in the marking state by the 4.7K Ohm pull-up and pull-down resistors.
Operating Distance
Data Rate (KBPS): 38.4 19.2 9.6 4.8
Maximum Distance (km): 1.2 2.0 2.5 3.5 (using 24 AWG wire)
Power
At the RS-422/485 side, unit is powered by an external power supply (+9VDC to +12VDC@200mA) by a AC/DC adapter. At the RS-232 side It powered by RS-232 signals TXD,RTS or DTR. You only need one of these signals, the ground signals in two sides are different.
Switches:
RS-422/RS-485 switch selectable for RS-422/485 operation mode. If you set unit to RS-422 mode, then it can convert the TD and RD signals of RS-232 into balanced Dual –duplex RS-422 signals. If you set unit to RS-485 mode, then it can convert the TD and RD signals of RS-232 into balanced Halfl –duplex RS-485 signals.
LED light
One LED indicates sending data to (RED) or receiving data from (GREEN) RS-422/485 bus.
Isolation:
Optical Isolation is rated at 2500V.
Dimensions:
8mm x 75mm x 20mm
Environment:
0* to 50* C
5% to 95% relative humidity.
Product Description
The AN-OS-RS-232/422/485 is a series of a bi-directional interface converters. AN-OS-RS-232/422/485 optically isolate and convert unbalanced, full or half-duplex RS-232 signals to 0ptically isolated, balanced, full or halfduplex RS-422 or RS-485 signals at baud rates up to 115.2 kbps.
These units also surge suppress the RS-422/485 lines. They feature Send Data Control circuitry so no software control of handshake lines is required in RS-485 mode. AN-OS-RS-232/422/485 has built-in isolators for high voltage (2500V) protection. it provides Point-to-Point, Multidrop and Simplex Operations. AN-OS-RS-232/422/485 can be powered from the DC 9V, 200mA power adapter. One slide switches are used to configure its operation mode.
Sản phẩm khác
-
Ethernet to V.35 converter
Ethernet to V.35 converter provide conversion from V.35 channel to Ethernet interface, and delivers Ethernet services over existing V.35 lines, RJ-45 type port for Ethernet.
-
Port Powered RS-232 to RS-422 Interface Converter
AN-PP-RS-232-422 is a lightweighted, compact and robust port powered RS-232 to RS-422 Interface Converter
-
RS-232 to CMOS/TTL converter
AN-RS-232-TTL converter provides low cost solution for converting the RS-232 serial com port generated signals to CMS/TTL level signals for prototype or testing low level microprocessor or microcontroller based systems
-
Port Powered RS-232 to RS-485 Interface Converter (4-bit terminal)
AN-PP-RS-232-485 is a lightweighted, compact and robust port powered RS-232 to RS-422 Interface Converter
-
Port Powered RS-232 To RS-485 Interface Converter
Port Powered RS-232 To RS-485 Interface Converter (6-bit terminal)
-
Port Powered ultra-high Speed RS-232 To RS-485 Interface Converter
AN-PP-RS-232-485/NH is a lightweighted, compact and robustultra-high speed port powered RS-232 to RS-485 Interface Converter
-
RS-232 to RS-422/485 Photoelectric Isolation Interface Converter
AN-PH-RS-232/422/485 is RS-232 to RS-422/485 Photoelectric Isolation Interface Converter
-
Industrial Class Wall-Mounted Photo-isolation RS-232/RS-422/RS-485 Interface Converter
AN-ISWM-RS-232/422/485 Industrial Class Wall-Mounted Photo-isolation Interface Converter is compatible with RS-232C, RS-422, RS-485
-
Port-Powered RS-232 Isolator, 9 Pin, 2 Channel
AN-IS-RS232 optically isolates and protects the transmit and receive lines of your RS-232 port from ground loops and power surges up to 2500V RMS for one minute.
-
Full metal housing, anti-static, powerful anti-jamming capacity RS-422/485 Photoelectric Isolation Data Repeaters
AN-DR-RS-422-485 data repeater is a kind of data relay communication product of photoelectric isolated RS-422/RS-485.
-
4-port/8-port RS-485 hub
AN-H-RS485-4(8) is a RS-485 bus split hub specially designed to meet the demand of RS-485 system in complicated electromagnetic field environment, avilable in 4 and 8 port versions
-
RS-232 extender: Extends the communication distance of serial port RS-232 to 12 kilometers
AN-EXT-RS-232 extends full-duplex transmission of asynchronous data over four wires (two twisted pairs).
-
RS-232- V.35 / X. 21 / RS-449 / RS-530 interface converter / protocol converter
AN-RS series interface converter provides RS-232 protocol conversion to V.35, X.21 or RS-449/RS530 interface full-duplex bi-directional mode.
-
AN-RS-485-MOD 1 port Mobdus gateway / converter
3-in-1 RS-232/422/485 interface Max.230Kbps Serial interface and 10/100 Mbps Ethernet MODBUS gateway / converter
-
NPort 5100A Series (Moxa) -1-port RS-232/422/485 serial device servers
The NPort® 5100A device servers are designed to make serial devices network-ready in an instant and give your PC software direct access to serial devices from anywhere on the network.
-
NPort 5100 Series 1-port RS-232/422/485 serial device servers
NPort 5100 device servers are designed to make serial devices network-ready in an instant. The small size of the servers makes them ideal for connecting devices such as card readers and payment terminals to an IP-based Ethernet LAN.
-
NPort P5150A Series :1-port RS-232/422/485 PoE serial device servers
NPort® P5150A device servers are designed to make serial devices network-ready in an instant. It is a power device and is IEEE 802.3af compliant, so it can be powered by a PoE PSE device without an additional power supply.
-
NPort 5200 Series: 2-port RS-232/422/485 serial device servers
The NPort 5200 serial device servers are designed to make your industrial serial devices Internet-ready in no time. The compact size of NPort 5200 serial device servers makes them the ideal choice for connecting your RS-232 (NPort 5210/5230/5210-T/5230-T)
-
NPort 5600 Series: 8 and 16-port RS-232/422/485 rackmount serial device servers
Features and Benefits
- Standard 19-inch rackmount size
- Easy IP address configuration with LCD panel (excluding wide-temperature models)
- Configure by Telnet, web browser, or Windows utility
- Socket modes: TCP server, TCP client, UDP
- SNMP MIB-II for network management
- Universal high-voltage range: 100 to 240 VAC or 88 to 300 VDC
- Popular low-voltage ranges: ±48 VDC (20 to 72 VDC, -20 to -72 VDC)