Trang chủ / Sản phẩm /

Port-Powered RS-232 Isolator, 9 Pin, 2 Channel

AN-IS-RS232 optically isolates and protects the transmit and receive lines of your RS-232 port from ground loops and power surges up to 2500V RMS for one minute.


AN-IS-RS232 optically isolates and protects the transmit and receive lines of your RS-232 port from ground loops and power surges up to 2500V RMS for one minute.


  • Product features:
    ● Protect serial port, inhibit static and surge,
    prevent ground loop and surge damaging devices
    ● Adopt latest high voltage photoelectric parts,
    powerful anti-jamming capacity
    ● Support RS-232 asynchronous communication standard,
    direct insert into RS-232 interface serially, convenient operation
    ● Transmission speed up to 57.6kbps
    ● Compact size, optional manifold signals and suitable
    for various devices.
  • Performance parameters:
    ●Interface: Conform to EIA RS-232 and CCITT V.24asynchronous protocols
    ●Connector: Both sides use DB9 connectors
    ●Transmission mode: Asynchronous, full duplex, fully transparent
    ●Isolation voltage : 2500V sequence or 7500V impluse
    ●Speed: Maximum 57.6 kps
    ●Power supply: supply electricity from RS-232 port (TXD,RTS OR DTR)
    ●Size: 6.8×5.5×1.6cm / 6.8×3.4×1.6cm
    ●Weight: 50g or 30g
    ●Working environment: 0 to 50℃ (0%—95% RH)
    ●Housing:  ABS plastic
  • Application fields:
    ●Bank, railway, electric power, post office, insurance, finance, administrative organs
    ●Various multi-user systems including UNIX
    ●Protect various multi-user terminals and hosts
    ●Protect program controlled exchanger, charge terminal, attendant
    ●Protect satellite receiver
    ●protect multi-user card
    ●protect non-ground RS-232 device

Interface
Conforms to EIA RS-232 standards

Connectors and signals
DB-9 female connector on the RS-232 DCE side and DB-9 male connector on the RS-232 DTE side.

RS-232 DCE Side:
Connector: DB-9 Female.

Signals: Use Pins 3 (RXD)and 2 (TXD) Pins 7 (RTS) and 8 (CTS) are tied together Pins 4 (DTR), 6 (DSR), and 1 (CD) are tied together.

RS-232 DTE Side:
Connector: DB-9 male.

Signals: Use Pins 3 (TXD ) and 2 (TXD) Pins 7 (RTS) and 8 (CTS) are tied together Pins 4 (DTR), 6 (DSR), and 1 (CD) are tied together.

Data Rate :  300 to 57.6KBPS

Dimensions:

2.4”L x 1.3”W x 0.66”H
(6.1L x 3.3W x 1.7H cm)

Connection diagram:

Product Description

The AN-IS-RS232 optically isolates and protects the transmit and receive lines of your RS-232 port from ground loops and power surges up to 2500V RMS for one minute.The data stream is converted from an electrical pulse to an optical beam, then back to an electrical pulse. Because there is no electrical connection between the DTE and DCE sides of the isolator, the AN-IS-RS232, unlike a surge suppressor, will not pass large sustained power surges through to your equipment.

This isolator will protect both the transmit and receive lines at baud rates up to 57.6K without the need of an external power supply. Power is derived through the transmit and handshake lines. Special circuitry allows the AN-IS-RS232to be powered regar-dless of the state of the handshake lines. At least one handshake line must be connected on each side of the isolator. Note that handshake line signals are not passed through the isolator.

Sản phẩm khác

  • Ethernet to V.35 converter

    Ethernet to V.35 converter

    Ethernet to V.35 converter provide conversion from V.35 channel to Ethernet interface, and delivers Ethernet services over existing V.35 lines, RJ-45 type port for Ethernet.

  • RS-232 to CMOS/TTL converter

    RS-232 to CMOS/TTL converter

    AN-RS-232-TTL converter provides low cost solution for converting the RS-232 serial com port generated signals to CMS/TTL level signals for prototype or testing low level microprocessor or microcontroller based systems

  • 4-port/8-port RS-485 hub

    4-port/8-port RS-485 hub

    AN-H-RS485-4(8) is a RS-485 bus split hub specially designed to meet the demand of RS-485 system in complicated electromagnetic field environment, avilable in 4 and 8 port versions

  •  NPort 5200 Series:  2-port RS-232/422/485 serial device servers

    NPort 5200 Series: 2-port RS-232/422/485 serial device servers

    The NPort 5200 serial device servers are designed to make your industrial serial devices Internet-ready in no time. The compact size of NPort 5200 serial device servers makes them the ideal choice for connecting your RS-232 (NPort 5210/5230/5210-T/5230-T)

  •  NPort 5600 Series: 8 and 16-port RS-232/422/485 rackmount serial device servers

    NPort 5600 Series: 8 and 16-port RS-232/422/485 rackmount serial device servers

    Features and Benefits

    • Standard 19-inch rackmount size
    • Easy IP address configuration with LCD panel (excluding wide-temperature models)
    • Configure by Telnet, web browser, or Windows utility
    • Socket modes: TCP server, TCP client, UDP
    • SNMP MIB-II for network management
    • Universal high-voltage range: 100 to 240 VAC or 88 to 300 VDC
    • Popular low-voltage ranges: ±48 VDC (20 to 72 VDC, -20 to -72 VDC)

     

    MOXA

Hotline: 0919.900.247