Home / Products /

NPort 5100A Series (Moxa) -1-port RS-232/422/485 serial device servers

The NPort® 5100A device servers are designed to make serial devices network-ready in an instant and give your PC software direct access to serial devices from anywhere on the network.


Features and Benefits

  • Power consumption of only 1 W
  • Fast 3-step web-based configuration
  • Surge protection for serial, Ethernet, and power
  • COM port grouping and UDP multicast applications
  • Screw-type power connectors for secure installation
  • Real COM/TTY drivers for Windows and Linux
  • Standard TCP/IP interface and versatile TCP and UDP operation modes
  • Connects up to 8 TCP hosts

Introduction

The NPort® 5100A device servers are designed to make serial devices network-ready in an instant and give your PC software direct access to serial devices from anywhere on the network. The NPort® 5100A device servers are ultra-lean, ruggedized, and user-friendly, making simple and reliable serial-to-Ethernet solutions possible.

 

A Greener Serial-to-Ethernet Solution

The MiiNe is a small but powerful Arm-based serial-to-Ethernet SoC with RAM and Flash embedded. With the MiiNe inside, the NPort® 5110A Series' power consumption is less than 1 W. The NPort® 5100A Series saves at least 50% on power consumption compared to existing solutions on the market, helping engineers meet the tough environmental compliance challenges found in today’s industrial environments.

 

Surge Protection for Serial, Ethernet, and Power

Surge, which is typically caused by high voltages that result from switching and lightning transients, is a common threat to all electrical devices. Moxa’s leading-edge surge immunity solution, which is applied to the NPort® 5100A’s serial, power, and Ethernet lines, is tested and proven compliant with IEC 61000-4-5. This state-of-the-art surge protection provides a robust serial-to-Ethernet solution that can protect electrical devices from voltage spikes and withstand electrically noisy environmental conditions.

3-Step Web-Based Configuration

The NPort® 5100A’s 3-step web-based configuration tool is straightforward and user-friendly. The NPort® 5100A’s web console guides users through three simple configuration steps that are necessary to activate the serial-to-Ethernet application. With this fast 3-step web-based configuration, a user only needs to spend an average of 30 seconds to complete the NPort® settings and enable the application, saving a great amount of time and effort.

Easy to Troubleshoot

NPort® 5100A device servers support SNMP, which can be used to monitor all units over Ethernet. Each unit can be configured to send trap messages automatically to the SNMP manager when user-defined errors are encountered. For users who do not use SNMP manager, an email alert can be sent instead. Users can define the trigger for the alerts using Moxa’s Windows utility, or the web console. For example, alerts can be triggered by a warm start, a cold start, or a password change.

MOXA

Other

  • Ethernet to V.35 converter

    Ethernet to V.35 converter

    Ethernet to V.35 converter provide conversion from V.35 channel to Ethernet interface, and delivers Ethernet services over existing V.35 lines, RJ-45 type port for Ethernet.

  • Port Powered RS-232 to RS-422 Interface Converter

    Port Powered RS-232 to RS-422 Interface Converter

    AN-PP-RS-232-422 is a lightweighted, compact and robust port powered RS-232 to RS-422 Interface ConverterAN-PP-RS-232-422 is a lightweighted, compact and robust port powered RS-232 to RS-422 Interface Converter

  • RS-232 to CMOS/TTL converter

    RS-232 to CMOS/TTL converter

    AN-RS-232-TTL converter provides low cost solution for converting the RS-232 serial com port generated signals to CMS/TTL level signals for prototype or testing low level microprocessor or microcontroller based systems

  • 4-port/8-port RS-485 hub

    4-port/8-port RS-485 hub

    AN-H-RS485-4(8) is a RS-485 bus split hub specially designed to meet the demand of RS-485 system in complicated electromagnetic field environment, avilable in 4 and 8 port versions

  • NPort 5200 Series: 2-port RS-232/422/485 serial device servers

    NPort 5200 Series: 2-port RS-232/422/485 serial device servers

    The NPort 5200 serial device servers are designed to make your industrial serial devices Internet-ready in no time. The compact size of NPort 5200 serial device servers makes them the ideal choice for connecting your RS-232 (NPort 5210/5230/5210-T/5230-T)

  • NPort 5600 Series: 8 and 16-port RS-232/422/485 rackmount serial device servers

    NPort 5600 Series: 8 and 16-port RS-232/422/485 rackmount serial device servers

    Features and Benefits

    • Standard 19-inch rackmount size
    • Easy IP address configuration with LCD panel (excluding wide-temperature models)
    • Configure by Telnet, web browser, or Windows utility
    • Socket modes: TCP server, TCP client, UDP
    • SNMP MIB-II for network management
    • Universal high-voltage range: 100 to 240 VAC or 88 to 300 VDC
    • Popular low-voltage ranges: ±48 VDC (20 to 72 VDC, -20 to -72 VDC)

     

    MOXA

Hotline: (+84) 919.900.247